To close the hood, push the hood down to lock it in place. The Yamaha Adjustable Sponsons can be adjusted to enhance watercraft performance according to operator preference and oper- ating conditions. If the gauge can be inserted into the gap, replace the plug with a new one. Remove the bolts and the direct ignition coils. So visit your authorized Yamaha dealer to get all the facts.
A collision could result in severe injury or death. However, the operator may adjust the trolling speed as part of the usual maintenance routine. The short time spent checking the acquired through practice over a period of watercraft will reward you with added safety time. Is the power input line normal? If debris is difficult to remove, consult your Yamaha dealer. You should know that a helmet could help pro- tect you in certain kinds of accidents and that it could also injure you in others. Remove the bolts 1 on both sponsons.
So your enjoyment includes a responsibility to treat these other people, and the lands, waters, and wildlife with respect and courtesy. You may still have some turning ability immediately after releasing the throttle, but once the engine slows down, the watercraft will no longer respond to han-. Continuing to operate at higher speeds could result in severe engine damage. Relay Coil Ground Line InspectionRemove the safety lanyard switch from the engine stop switch. If necessary, have a Yamaha dealer repair the oil injection sys- tem.
Screw the spark plug in the cylinder head by hand to prevent cross-threading. Remove any weeds or debris from around the drive shaft, impeller, pump housing, and jet thrust nozzle. Always consult local boat- latory or advisory information. To check for proper operation of the cool- ing system, check that water is being dis- charged from the pilot outlets. The fuel filter should be replaced once a year or after every 200 hours of operation, or if water is found in the filter. If you maintain the battery yourself, read carefully the instructions for the tool and. If the clearance is out of specification, disassemble and inspect the impeller and impeller housing area.
Spray a rust inhibitor, such as Yamaha Silicone Protectant and Lubricant, on metallic parts to minimize corrosion. This position will also help the watercraft get up on plane more quickly. To check these switches place the water- craft in the water to provide adequate cooling. Pump out the engine oil with a commercially available Fluid Evacuator from the oil filler hole and drain pipe, to drain the oil tank and oil pan. Perform the same lubrication procedure for joint hole. When the sailing vessel is overtaking the course and speed.
It should be smooth over the complete range, and spring back to the idle position when released. To remove the seat: Pull the seat latch 1 up, and then pull the seat off. Check the ground line of the starter relay switch. Starting the engine immediately generates some thrust. Continuing to operate at higher speeds could result in severe engine damage. Clean any oil from the cartridge seating surface of the engine and the oil filter tray.
Make sure no obstructions, boats or swimmers are near the beach. Also, check that the clamp is installed on the oil tank securely. So if it's a WaveRunner battery or a WaveRunner basket of parts, we're here to help. If the air temperature is below 10°C 50°F , let the engine idle for an additional 5 minutes a total of 10 minutes. Yamaha recommend charging battery by a Yamaha dealer or a battery dealer. To ventilate the engine compartment, remove seat and front storage compart- ment. When transporting the watercraft on a trailer, secure the tie downs to the trailer through the bow eye and stern rope holes.
Take note of weather forecasts and the prevailing weather conditions before setting out on your watercraft. Start the engine, and then pull the engine shut-off cord 5 to remove the clip 4 from the engine shut-off switch. Remove the joint hoses from the clip s and disconnect the maintenance joint. See page 2-5 for seat, and 2-22 for front storage compartment. Check the throttle lever for smooth operation.
To install the seat: Insert the projection on the front of the seat into the stay on the deck, and then. Reinstall the drain pipe cap and tighten it. Exhaust fumes contain carbon monox- ide, a colorless, odorless gas that may cause loss of consciousness and death within a short time. Releasing the throttle completely produces only min- imum thrust. To lubricate and rustproof the inside of the throttle body, proceed as follows after confirming that the engine is stopped and cool.