Reduce the motor oil changeover intervals by half, if the sulfur content in the fuel is below 1%. Before you start operating the tractor, carefully read this Manual and strictly follow all instructions herein. If the engine is stopped, the tractor;. Air pressure in tires Check the tread condition and air pressure in the tires. To do that, raise the wheel.
If there are any plays or jamming of the. Belarus Tractor 611 Parts Manual can be very useful guide, and belarus tractor 611 parts manual play an important role in your products. Draining sediment from fuel tanks and fuel coarse filter Open the drain plugs 1 of the fuel tanks 2 and the drain plug 3 of the filter and drain sediment until clean fuel appears. Under normal conditions, set the minimum allowable pressure in tires for operation with trailed machines. Front driving axle number on the front part. Adjustments Adjusting front wheel track of steering booster without cylinder in steering linkage The front wheel track can be adjusted from 1,350 to 1,850 mm with 100 mm in- crements in case of symmetrical position of wheels and 50 in case of asymmetrical position.
It must be Check that terminals 2 under the above the protective mesh by 12 to 15 jackets A and plugs 1 are clean. Safety precautions warn other persons and persons working on the towed machines. When working with attached machines, set a higher tire pressure. Working with implements, use only the lift and floating positions of the lever. It is installed on the cab rear sup- port.
Flushing steering booster drain filter To flush the oil filter, proceed as follows: raise the facing; disconnect the oil ducts 7, 13 and 15, unscrew the bolts 5 fastening the cover 6 to the housing, remove the cov- er using two unmounting bolts. The problem is that once you have gotten your nifty new product, the belarus 802 tractor workshop repair service manual gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Oil level and condition in engine air cleaner tray Loosen the two nuts 1 and remove the tray 2 of the air cleaner 3. Put a support under the tractor rear part to provide secure and safe tractor posi- tion;. When selecting the re- quired gear, use the gear shift pattern.
Brake disk linings are oiled or worn out. Register a Free 1 month Trial Account. Blue fume is emitted from the exhaust pipe Ingress of oil into the combustion chamber as a re- Replace the worn-out parts of the cup-piston group. The applied materials provide protec- 600125053. Before you start operating the tractor, study the controls and instru- mentation and their functions. To adjust a steering rod joint, procede.
Turn on the pump only at the engine minimum idle speed. When mounting machines to the tractor, first make sure that no one is present in the zone of mounting the machine. Fix the lever 11 in the neutral position in- nism troducing the bolt 10 M10×60 to the hole on the lever 11 and the hole on the rear When assembled by the manufacturer, axle housing corresponding to it;. Checking backlashes in steering rod joints After each 250 service hours, check the joints by shaking them by hand or rotat- ing the steering wheel. Remove the plug 1 in the lower part of the fuel fine filter by 2 to 3 turns as per the figure and drain sediment until clean fuel free of water and dirt appears. Has two positions: Differential lock control knob;.
During operation, the left brace length can be changed from 395 to 510 mm depend- ing on the tractor delivery set and kind of 425-520 attached machines and equipment. Adjusting drain valve of centrifugal oil filter of engine If during the engine operation within the rated mode at normal temperature 80 to 100° C , the oil pressure has dropped be- low 0. Unscrew the six bolts 4 , remove the lock plate 6 and remove the shank 5. At that, to partially lock the machine in the working position, attach the limit chains 2 to the hole of the bracket 1 third from the bottom and to fully lock —. Turn off the pump for engine cold start or maintenance. In case of significant the levers connected with it. Before engaging a gear, engage the required range stage.
This manual should be kept near the machine for reference and periodically reviewed by all personnel who will come into contact with it. Slipping of the alternator driving belt. The problem is that once you have gotten your nifty new product, the belarus tractor 611 parts manual gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Using the handle of the power regulator if. Note the filter orientation in the oil line. Adjust the coupling by tightening the nut 2 of the rear shaft shank of the intermediate sup- port to ensure transfer of the required torque.
When operating the tractor under special. Use the climatic diesel fuel according to the Manual. Periodically after each 250 service hours as well as at each change of front wheel track check and as necessary adjust the wheel toe-in. Absence of a free pedal trav-. The trailers work at speeds determined by road conditions.