With pilot lit, depress and turn gas knob counter-clock-wise to on. Read the above safety information on this label. Replace the blower using the existing bracket. If you don't see your equipment listed please contact us at 1-800-258-3570 and we will be happy to assist you with all you laundry needs. This enables the blower to function properly. Turn gas knob counter-clockwiseto pilot.
Venting action is unsatisfactory if the flame extinguishes. Fasten to the roof on the top and sides. The stove, when installed with a blower, must be electrically connected and grounded in accordance with local codes. We recommend that exhaust vents that pass through unheated spaces be wrapped in a protective sleeve to minimize condensation and reverse flow symptoms. Pilot goes out while Gas piping is undersized. The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from your authorized dealer. It is recommended that the fireplace be secured in all installations.
Secure to the sleeve using 3 screws. Bring the gas line to the stove through either the opening in the pedestal back or through the floor directly beneath the pedestal base. Provide adequate accessibility clearance for servicing and operating the stove. Lift the door from its hinges to clean hinge pins and lubricate using high-tempdry graphite as necessary. Venting action is satisfactory if the flame stays lit. Never obstruct the front opening of the stove. If the match does not stay lit, turn the unit off and check for vent blockage or restriction.
Use a firestop when penetrating interior walls, floor or ceiling. These spacers must not be removed. Place the flashing over the air terminal and slide it underneath the sides and upper edge of the shingles. Check to see that all burner ports are burning. John Deere and its logos are the registered trademarks of the John Deere Corporation. Below you will find information regarding most of the Continental Girbau line of equipment. When lighting and re-lighting,the gas knob cannot be turned from pilot to off unless the knob is depressed slightly.
Do not fill this cavity with any type of material. Make weather-tightby sealing with caulking. None of these trademark holders are affiliated with Yesterday's Tractor Co. This same sealant maybe used on both the inner exhaust and outer intake vent pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the fireplace flue collar which must be sealed using the black high temperature sealant Mill Pac. Drywall dust will penetrate into the blower bearings causing irreparable damage and must be prevented from coming into contact with the blower or its compartment. Keep knob depressed for one minute, then release. We are more than happy to take your order over the phone.
Turn the gas knob clockwise to off. Turn on all electric power to the fireplace. If you do your own repairs, you need the parts manual. Immediately call a qualified service technician to inspect the fireplace and replace any part of the control system and any gas control which has been under water. Buff lightly with a clean dry cloth. For elevations between 2,000 and 4,500 feet above sea level, this fireplace must be de-ratedby 10% using the certified high altitude kit. A firestop must be placed on the bottom of each framed opening in a roof or ceiling that the venting system passes through.
A terminal shall not terminate directly above a sidewalk or paved driveway which is located betweeen two single family dwellings and serves both dwellings. Remote switch must be in the on position to ignite burner. Call 800-853-2651 and talk to our friendly sales staff. . Remove the combustion air cover plate and its gasket. Replacement of the glass should be done by a licensed or qualified service person. Any damage resulting from this condition is not covered by the warranty policy.
This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed from other manufacturers will nullify this warranty. To do this simply loosen the tighten the catch until both latches snap closed when closing the door. The location of windows, doors and the traffic flow in the room where the stove is to be located should be considered. Installation must be done in accordance with the installation instructions included with the product and all local and national building and fire codes. Verify proper operation after servicing.
Installation kits for various roof pitches are available from your Continental dealer. The vent should ex- tend, at least, 3 feet above its point of contact with the roof and, at least, 2 feet higher than any wall, roof or building within 10 feet. Any labour related to warranty repair is not covered. When the fireplace is installed at elevations above 4,500ft, and in the absense of specific recommendations from the local authority having jurisdiction, the certified high altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft. Flame is impinging on the - check that the logs are correctly positioned. Assure that a continuous gas flow is at the burner before closing the door.
Do not kink the flexible connector. What is the required vertical rise to the centre of the initial 90° elbow? Apply a bead of caulking all around and place a firestop spacer over the vent shield to restrict cold air from being drawn into the room or around the stove. In the event that the venting must be disassembled, care must be taken to reseal the venting. The blower power cord must be connected into a properly grounded receptacle. Because the flame is very efficient it will burn a very blue, almost transparent colour.