Reread the Belt Cleaner Life Counter. To open downloaded files you need acrobat reader or similar pdf reader program. Insert the two metal tabs located at the rear of the Cover into the two slots in the printer frame. Is the printer located in an area that is free of dust? Is the paper wrinkled, dimpled, or show any signs of having a high moisture content? Use two screws to secure the two Hinge Plates to the Front Cover Assembly, but tighten the screws only halfway. Check for continuity across the Fuser Fuse.
Go to step 9 Problem solved. Carefully slide the Main Paper Handling Assembly out of the printer and inspect the sheet of paper. Position the Inner Cover against the printer frame, making sure the top of the Cover is under the lip of the Top Cover. Swing the Paper Handling Turn Chute Assembly down into position and insert the front and rear pivot arms located at the bottom of the Paper Handling Turn Chute Assembly into the holes at the bottom of the Main Paper Handling Assembly. Inspect the two metal contacts that are located at the rear of the Oil Roll Assembly. Hook the Pick Up Spring onto the Pick Up Gear.
Remove Tray 1 from the printer. One or more of these components may have failed partially or completely. Remove the Controller Protective Cover. Unhook the Pick Up Spring from the Pick Up Gear. . Remove Tray 1 from the printer.
Firmly close the Feeder Cover. Does the error message still appear? Inspect the image on the sheet of paper just before the paper enter the Fuser. When moving the product or removing an option, use care not to injure your back or allow your hands to be caught in mechanisms. Base Engine Accumulative Images Processed Retrieving the Life Counters Data 1. All troubleshooting procedures contained herein assume that there are no breaks in the harnesses and cords and all connectors are plugged into the right positions. When you have released the latch, pull the Bracket down into the empty paper feeder. Do not touch the electrical contacts, gears, or laser beam devices.
Is the area free of paper scraps? While you are cleaning, inspect the interior of the printer for damaged wires, loose connections, toner leakage, and worn or damaged parts. Push the Cover onto the Frame, making sure the wire harnesses and the ground strap fit through the cutouts in the Cover. This chapter provides information about the following accessories. Reposition the Top Cover so the Exit Rolls fit through the cutouts in the left side of the Top Cover. Slide the Rear Pick Up Roll so the locking pin fits into the notch on the Roll. One or more of these components may have failed partially or completely. Reposition the Top Cover so the two screw holes at the rear of the Cover and the two holes at the front of the Cover line up with the screw holes in the printer frame.
Reach in through the empty paper feeder and use your hand to support the shaft as you press the Rear Feed Roll onto the shaft. Make sure that all parts, wiring and screws are returned to their original positions. One or more of these components may have failed partially or completely. Fuser Unit Accumulative Images Processed 8. Are consumables replaced at recommended intervals? Connect Serial Cable to Portable Computer's Serial Port refer to computer's user guide 3. Place your hand near, but not on, the Fuser Rolls. Slide the Fuser Unit out of the printer.
One or more of these components may have failed partially or completely. Slide the green Pre-Registration Knob off of the Pre-Registration Shaft Figure 1. From the Select Port list, select the port to which the printer is connected. Does the error message still appear? Use two screws to secure the Turn Chute to the printer frame. Precautions for Service Keep all disassembled parts in good order and keep tools under control so that none will be lost or damaged. One or more of these components may have failed partially or completely.
Precautions for storing the toner or imaging cartridge. Slide the Main Paper Handling Assembly out of the printer and inspect the back of the sheet of paper. Remove the Controller Protective Cover. Is the actuator free of damage? Slide Tray 1 back into the printer. Does the error message still appear? Slide the Main Paper Tray out of the printer. Minolta is a trademark of Minolta Co.
Manually actuate and deactuate the No Paper Sensor. Inspect the image on the Drum. Media is flat, especially on the leading edge. Shut off the other electrical equipment or relocate the printer to at least twenty feet away from the other devices. When the printer stops and a service message displays in the Status Display message window, turn the printer off and then back on.